Pm-1340gt 13x40 Ultra Precision Lathe Large Spindle Bore Taiwan 3ph Ships Free

THIS MACHINE COMES WITH A STAND, IF YOU WOULD LIKE A MACHINE WITHOUT THE STAND, PLEASE SEE OUR OTHER LISTING. Main Features Of This Machine. Extremely High Quality Lathe, meant for very high precision work, and suitable for every day use. Perfect for the professional user who is looking for the best available. 100% Made in Taiwan, no shortcuts taken, built to a very high level of quality.

Excellent machine for Gunsmithing use, Very Short Spindle, Ultra High Precision. Available in either Single or 3 Phase power, to match the users needs. High Precision, Hardened and Ground gears throughout headstock , which leads to extremely smooth and quiet running for a geared head lathe, and much longer life (Suitable for daily, professional use).

Leadscrews Are True Inch Pitch Screws (Not Metric Conversions Like Many), 10 Threads Per Inch. Highest Quality Lathe, Made in TAIWAN. Large 1-9/16 Spindle Bore clear through spindle for through-headstock work. Short Spindle Length, only 13-3/4, perfect for gunsmithing work. Extra thick spindle wall for extra rigidity, almost double when compared with most other.

Power feed on Carriage, and Cross Slide, both left and right, and in and out, for both turning. And facing operations with automatic feed. Allows for the best surface finish in all directions. Induction Hardened and Precision Ground Bed Ways to resist wear and give a long service life. All shafts in headstock hardened and ground along with gears which are precision ground, set in with a close tolerance fit, which leads to longer life and quiet running when compared with other geared head lathes.

Inch AND Metric thread cutting ability is a standard feature, NO CHANGE GEARS for any. Inch thread or feed rate, only change gears required are for Metric threads. 4 Travel Thread Dial, 32 tooth gear on thread dial, 8 TPI Main Leadscrew for easier threading. Using the half nut / thread dial. Large diameter, extra thick wall tail stock quill for more rigid and accurate tail stock operations.

Locking Tang in tail stock is provided. Removable Gap for larger diameter work when needed. High quality electronics used throughout machine, very reliable contactors, motors, etc. Slip Clutch is standard on feed rod, to help prevent overloading damage of feeds and allow the.

Use of a solid carriage stop for repetitive work. Precision Tapered Roller Bearings used in spindle, for the ultimate in long life, high precision. True INCH PITCH main lead screw, cross feed, and compound lead screws make it easy to use. For the INCH measurement System, yet still has the Metric readings on dials for the ultimate in.

Versatility for any job that may come about. Splash oil bath lubrication in Headstock, and Apron, for efficient lubrication, and long life, yet.

Simple and reliable, and does not require any filter changes or pump maintenance as with oil. Also no risk of losing oil flow to expensive parts as there can be with. Only Extremely High Precision Spindle Bearings are used, NACHI (Japan). Swing over cross slide: 6-1/2.

Spindle Center Line Distance from Floor: Approx. Spindle Taper, Internal: MT #5.

Spindle Mounting System: Cam Lock, D1-4. Spindle Speeds: 90-1600 RPM, 12 Steps. Lead Screw Diameter / Pitch: 7/8 / 8 TPI. Inch Thread Cutting Range: 4-112 TPI, 40 Different Threads. 25-7.5mm Pitch, 24 Different Threads.

Longitudinal Feed Range (Left and Right). 002.02 Inches Per Revolution.

Cross Feed Range (In and Out). 001.01 Inches Per Revolution. Spindle Length through headstock, Protruding End to D1-4 Chuck Mounting face: 13-3/4. Spindle Length through headstock, Protruding End to 3 Jaw Chuck face: 17-1/4. Tail Stock Quill Diameter / Travel / Taper: 1-9/16 / 4 / MT#3.

Main Motor Horsepower: 2 HP. 220 Volt, 3 Phase / 9 Amps Max. Machine Dimensions, Assembled with stand: 29W x 70L.

Machine Weight (without stand): 850 LBS Machine Weight (with Stand): 1,350 LBS. PM1340GT High Precision Lathe Steel Stand. Back Splash Guard High Precision NSK Spindle Bearings, +/. 0001 Spindle Runout Max 4 Way Tool Post Threading Dial (4 Travel Dial, 32 Tooth) Reducing Sleeve for headstock Dead Center for Headstock Steady Rest Dead Center for Tailstock Follow Rest Feed Rod Clutch Chip Tray Misc. Tools for operation D14 Camlock Quick Change Spindle 6, Ultra High Precision 3 Jaw Chuck, Autostrong SK Type. If you would like to stop in and see one in person, we are at. 1060 Montour West Industrial Park.

We are machinists here too, so we know what we sell. This is really a top quality machine, and will last a long, long time. AND we are here for support too. We sell these machines regularly, we know them inside and out, and have been in business for many years, so if there is any question, we can help. Check out our other auctions for more lathes and mills.

The item "PM-1340GT 13X40 ULTRA PRECISION LATHE LARGE SPINDLE BORE TAIWAN 3PH SHIPS FREE" is in sale since Monday, October 14, 2019. This item is in the category "Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Equipment\Metalworking Lathes".

The seller is "qualitymachinetools" and is located in Pittsburgh, Pennsylvania. This item can be shipped to United States, Canada.

Model: PM-1340GT-PEP-3PH & PM-1340GT-STAND
Country/Region of Manufacture: Taiwan
MPN: PM-1340GT-PEP-3PH & PM-1340GT-STAND
Brand: Precision Matthews